crane for dinhy
crane for dinhy
hello everyone long time i dont post , any way i was wondering if anyone on here has installed a lift, davit, crane what ever its called on the bow (deck) of 33 fbc before and what brand or type. I have a very light 110# inflatable with a little yamaha 4hp 4 stroke about 45 lbs. and i need to find something to lift it with the motor on to my deck ,PLEASE ANY SUGGESTIONS... Thanx in advance..Pete
The picture of Doug's boat has a small boat on the bow maybe he can help you. Where would you get the support for a lift, run it through the deck in the closet in the vee birth. Would that leave enough room for a boat too? I've seen the connections to mount one on the swim platform but never a lift on the bow of a 33 Bertram. Have you tried asking the guys on the Bertram 31 web site, they may have some ideas. Buzz buzzk 1988 Bertram 33 FBC Buzz Off Morehead City, NC
buzzk 1988 Bertram 33 FBC Cummins 6BTA's Buzz Off Morehead City, NC
I'm sure if there is something that will work you can find it in the Miami-Ft. Lauderdale area. That's what I like about Ft. Lauderdale, you can find just about anything you need for a boat. Buzz buzzk 1988 Bertram 33 FBC Buzz Off Morehead City, NC
buzzk 1988 Bertram 33 FBC Cummins 6BTA's Buzz Off Morehead City, NC
My RIB is only 8'6". It weighs around 95 lbs which is just light enough for my wife and I to drag on and off. I have a 10hp 4 stroke (88lbs) hanging on the rear bulkhead. Regards, Doug L. 1986 33 Bertram FBC Queen Elizabeth Marblehead, MA [img]http://www.bertram33.com/photogallery/p ... sabeth.jpg[/img]
Regards, Doug L.
1986 33 Bertram FBC Cummins 6BTA's Queen Elizabeth
Marblehead, MA

1986 33 Bertram FBC Cummins 6BTA's Queen Elizabeth
Marblehead, MA

Marquip is the davit of choice. At least in So. Fl. I helped a guy put one on a POS Crusiers. Basically the pipe goes all the way thru the deck and into a plate fiberglassed into the hull. It routes between the fwd & rear cabin bulkhead. I think on a 33 it will go right through the middle of your front bunk. Personally I think putting something on the 33 is not a good idea. There isn't enough support in the deck to take the stress. And you can't go all the way down to the bottom for support. I have a 11 ft and a 15 hp. Roll it up and take it to where ever. If I need to move any distance , I just stuff it in the cockpit hanging over (with engine off) and toss it out again when I get to the next anchorage. Gene Dugan Boca Raton, Fl. "Nauti Marie" 1989 33 FBC
Gene Dugan Boca Raton, Fl. "Nauti Marie" 1989 33 FBC 2007 8.1 Crusaders SOLD 2000 Pursuit 2870 Offshore Twin 2016 Suzuki 200s
hey guys thanx for input i have decided to keep my hurley davits and secure the dinghy on swim platform with 2 inch ss straps hooked to ss hardware on swim platform.Since i will be covering the name of my boat on the transom do i have to paint the boats name on the dinghy to comply with coast guard regs.??I am not sure but i would like to prevent a problem with the coast guard. Please help me with that question and thanx again..Pete
quote:Since i will be covering the name of my boat on the transom do i have to paint the boats name on the dinghy to comply with coast guard regs.??I am not sure but i would like to prevent a problem with the coast guard. I've wondered that myself, but have motored right on by USCG cutters that were pulling over boats coming in from Bahamas left and right, for any particular reason just to search them - with my dinghy tied across my transom and obscuring my name... and they never bother me. I wouldn't worry about it, but it might technically break some rule. Some of these certified Captains here should know the exact answer to that. I've seen plenty of people do it but also have never seen a vessel name painted on the bottom of a dinghy "Island Time" 1987 Bertram 33 SF Melbourne, FL [img]http://www.bertram33.com/photogallery/p ... d_Time.jpg[/img]
"Island Time" 1987 Bertram 33 SF 3208T Cats


Yup, technically you need to show the boat name and hailing port. Lot of people here paint the name and port on the dingy bottom. Quite common. Gene Dugan Boca Raton, Fl. "Nauti Marie" 1989 33 FBC
Gene Dugan Boca Raton, Fl. "Nauti Marie" 1989 33 FBC 2007 8.1 Crusaders SOLD 2000 Pursuit 2870 Offshore Twin 2016 Suzuki 200s
quote:Originally posted by captgene Lot of people here paint the name and port on the dingy bottom. Quite common. Same up in my neck of the woods. I hate the way that looks, so I always haul it up on the bow. Regards, Doug L. 1986 33 Bertram FBC Queen Elizabeth Marblehead, MA [img]http://www.bertram33.com/photogallery/p ... sabeth.jpg[/img]
Regards, Doug L.
1986 33 Bertram FBC Cummins 6BTA's Queen Elizabeth
Marblehead, MA

1986 33 Bertram FBC Cummins 6BTA's Queen Elizabeth
Marblehead, MA

-
justintime2
- Lieutenant

- Posts: 36
- Joined: Tue Jan 15, 2019 1:21 pm
Doug can you tell me how you have your outboard motor mounted in the cockpit? I am thinking behind the ladder, to the port side , but would need to do something about making it stronger. quote:Originally posted by dougl33 quote:Originally posted by captgene Lot of people here paint the name and port on the dingy bottom. Quite common. Same up in my neck of the woods. I hate the way that looks, so I always haul it up on the bow. Regards, Doug L. 1986 33 Bertram FBC Queen Elizabeth Marblehead, MA [img]http://www.bertram33.com/photogallery/p ... sabeth.jpg[/img]
1987 33 FBC Merc 454




